答案查看网,轻松搜题/搜资源
登录
×
登录账号
记住密码
立即注册
忘记密码
×
注册
使用微信扫描二维码,获取账号密码后免费查看答案
前往登录
忘记密码
×
忘记密码
使用微信扫描下方二维码,即可找回您的账号密码
前往登录
立即注册
搜题/搜资源
【单选题】【消耗次数:1】
There were some ____ flowers on the table.
①
artificial
②
unnatural
③
false
④
unreal
参考答案:
复制
纠错
相关题目
【单选题】
In a room above the store, where a party __________,some workers were busily setting the table.
①
was to be held
②
has been held
③
will be held
④
is being held
查看完整题目与答案
【单选题】
There [填空] some chopsticks on the table.
①
are
②
is
③
have
④
was
查看完整题目与答案
【单选题】
He’s going to [填空] her some flowers.
①
buy
②
bought
③
buying
④
offering
查看完整题目与答案
【单选题】
We looked for a table to sit down, but they were all ____.
①
reserved for
②
engaged in
③
used up
④
taken up
查看完整题目与答案
【单选题】
An experiment suggests that flowers have some____________ ways of keeping time.
①
modern
②
mysterious
③
military
④
mixed
查看完整题目与答案
【单选题】
I ___remember to send my mother some flowers. Its her birthday tomorrow.
①
must
②
have to
③
could
查看完整题目与答案
【单选题】
Some scientists____________ that flowers open at particular times because their internal clocks tell them to do so.
①
receive
②
make
③
believe
④
talk
查看完整题目与答案
【单选题】
There were some chairs left over[] everyone had sat down.
①
when
②
until
③
that
④
where
查看完整题目与答案
【单选题】
The inspector ____ his fingers over the sheet of newspaper. There were some marks on the surface of the paper.
①
turned
②
set
③
held
④
ran
查看完整题目与答案
【单选题】
There is [填空] on the table.
①
two cups of water
②
some waters
③
some water
④
any waters
查看完整题目与答案
随机题目
【判断题】
在批量生产的情况下,用直接找正装夹工件比较合适。
①
正确
②
错误
查看完整题目与答案
【判断题】
加工表面层产生的残余压应力,能提高零件的疲劳强度。
①
正确
②
错误
查看完整题目与答案
【判断题】
磨削内孔时,在工件孔径允许的条件下,应尽量选用大直径的砂轮。
①
正确
②
错误
查看完整题目与答案
【单选题】
前刀面上出现积屑瘤对()有利。
①
粗加工
②
半精加工
③
光整加工
④
精加工
查看完整题目与答案
【单选题】
在()生产中一般使用通用夹具。
①
大量
②
成批
③
大批大量
④
单件小批
查看完整题目与答案
【单选题】
粗基准选择时,若要保证某重要表面余量均匀,则应选择()
①
余量小的表面
②
该重要表面
③
半精加工之后
④
任意
查看完整题目与答案
【单选题】
先将工件在机床或夹具中定位,调整好刀具与定位元件的相对位置,并在一批零件的加工过程中保持该位置不变,以保证工件被加工尺寸的方法称为()。
①
调整法
②
试切法
③
自动控制法
④
定尺寸刀具法
查看完整题目与答案
【单选题】
车削螺纹时,产生螺距误差、影响误差大小的主要因素是()
①
主轴回转精度
②
导轨误差
③
传动链误差
④
测量误差
查看完整题目与答案
【单选题】
机床型号中“G”代表()。
①
割床
②
锯床
③
钻床
④
齿轮加工机床
查看完整题目与答案
【单选题】
在零件的加工过程中,更换刀具属于()时间。
①
休息与生理需要时间
②
辅助时间
③
布置工作地时间
④
基本时间
查看完整题目与答案